You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
66 lines
2.5 KiB
66 lines
2.5 KiB
#include "board.h" |
|
|
|
|
|
// |
|
// The following parameters need to be defined for each project's inital clock setup (used in system.c)) |
|
// |
|
#define FRO_FREQ_VAL 2 // 0 = 18 MHz |
|
// 1 = 24 MHz (reset value) |
|
// 2 = 30 MHz |
|
|
|
#define MAINCLKSEL_VAL 0 // 00 = fro (reset value) |
|
// 01 = external_clk |
|
// 10 = lposc_clk |
|
// 11 = fro_div |
|
|
|
#define SYSAHBCLKDIV_VAL 1 // 0x00 = system_ahb_clk disabled (use with caution) |
|
// 0x01 = divide_by_1 (reset value) |
|
// 0x02 = divide_by_2 |
|
// 0xFF = divide_by_255 |
|
|
|
#define CLKIN_CLK_VAL 12000000 // External Clock (CLKIN) frequency [Hz] must be in the range of 1 MHz to 25 MHz |
|
|
|
#define EXT_CLOCK_FORCE_ENABLE 0 // Force config. and enable of external_clk for use by other than main_clk |
|
// 0 = external_clk will be configured and enabled only if needed by main_clk or sys_pll0_clk. |
|
// 1 = external_clk will be configured and enabled (available for other, e.g. clock out). |
|
|
|
// End of clocks configuration section |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
// |
|
// The following parameters need to be defined for projects that use the debug UART (used in serial.c) |
|
// |
|
#define DBGUART 0 // Choose the index for the debug UART (0 for UART0, 1 for UART1, etc.) |
|
#define DBGBAUDRATE 9600 // Choose the baud rate for the debug UART |
|
#define USE_VCOM_PORT 1 // '1' to use VCOM serial port, '0' to use user-defined port pins for debug UART |
|
|
|
#if (USE_VCOM_PORT == 1) |
|
#define DBGTXPIN TARGET_TX // For VCOM serial port (see board.h) |
|
#define DBGRXPIN TARGET_RX // For VCOM serial port (see board.h) |
|
#else |
|
#define DBGTXPIN P0_15 // Use with USB-to-RS232 break-out cable (choose your own favorite TxD pin) |
|
#define DBGRXPIN P0_14 // Use with USB-to-RS232 break-out cable (choose your own favorite RxD pin) |
|
#endif |
|
|
|
// |
|
// The following are so the debug UART is selectable from any UART on the device (used in Serial.c) |
|
// |
|
#define __CONCAT(x,y,z) x##y##z |
|
#define __XCONCAT(x,y,z) __CONCAT(x,y,z) |
|
|
|
#define INDEX DBGUART |
|
#define pDBGU __XCONCAT(LPC_USART,INDEX,) |
|
#define DBGU __XCONCAT(UART,INDEX,) |
|
#define DBGUTXD __XCONCAT(U,INDEX,_TXD) |
|
#define DBGURXD __XCONCAT(U,INDEX,_RXD) |
|
#define DBGURST __XCONCAT(UART,INDEX,_RST_N) |
|
#define DBGUIRQ __XCONCAT(UART,INDEX,_IRQn) |
|
|
|
|