Initial commit

inc/chip_setup.h

@@ -0,0 +1,66 @@
+#include "board.h"
+
+
+//
+// The following parameters need to be defined for each project's inital clock setup (used in system.c))
+// 
+#define FRO_FREQ_VAL 2             // 0 = 18 MHz
+                                   // 1 = 24 MHz (reset value)
+                                   // 2 = 30 MHz
+
+#define MAINCLKSEL_VAL 0           // 00 = fro (reset value)
+                                   // 01 = external_clk
+                                   // 10 = lposc_clk
+                                   // 11 = fro_div
+
+#define SYSAHBCLKDIV_VAL 1         // 0x00 = system_ahb_clk disabled (use with caution)
+                                   // 0x01 = divide_by_1 (reset value)
+                                   // 0x02 = divide_by_2
+                                   // 0xFF = divide_by_255
+
+#define CLKIN_CLK_VAL 12000000     // External Clock (CLKIN) frequency [Hz] must be in the range of  1 MHz to  25 MHz     
+
+#define EXT_CLOCK_FORCE_ENABLE 0   // Force config. and enable of external_clk for use by other than main_clk
+                                   // 0 = external_clk will be configured and enabled only if needed by main_clk or sys_pll0_clk.
+                                   // 1 = external_clk will be configured and enabled (available for other, e.g. clock out).
+
+// End of clocks configuration section
+
+
+
+
+
+
+
+
+
+
+//
+// The following parameters need to be defined for projects that use the debug UART (used in serial.c)
+//
+#define DBGUART 0                  // Choose the index for the debug UART (0 for UART0, 1 for UART1, etc.)
+#define DBGBAUDRATE 9600           // Choose the baud rate for the debug UART
+#define USE_VCOM_PORT 1            // '1' to use VCOM serial port, '0' to use user-defined port pins for debug UART
+
+#if (USE_VCOM_PORT == 1)
+  #define DBGTXPIN TARGET_TX       // For VCOM serial port (see board.h)
+  #define DBGRXPIN TARGET_RX       // For VCOM serial port (see board.h)
+#else
+  #define DBGTXPIN P0_15           // Use with USB-to-RS232 break-out cable (choose your own favorite TxD pin)
+  #define DBGRXPIN P0_14          // Use with USB-to-RS232 break-out cable (choose your own favorite RxD pin)
+#endif
+
+//
+// The following are so the debug UART is selectable from any UART on the device (used in Serial.c)
+//
+#define __CONCAT(x,y,z) x##y##z
+#define __XCONCAT(x,y,z) __CONCAT(x,y,z)
+ 
+#define INDEX   DBGUART
+#define pDBGU   __XCONCAT(LPC_USART,INDEX,)
+#define DBGU    __XCONCAT(UART,INDEX,)
+#define DBGUTXD __XCONCAT(U,INDEX,_TXD)
+#define DBGURXD __XCONCAT(U,INDEX,_RXD)
+#define DBGURST __XCONCAT(UART,INDEX,_RST_N)
+#define DBGUIRQ __XCONCAT(UART,INDEX,_IRQn)
+

inc/lib_ENS_II1_lcd.h

@@ -0,0 +1,23 @@
+/*
+ * lib_ENS_II1_lcd.h
+ *
+ *  Created on: 9 oct. 2018
+ *  Modified on sept. 2019
+ *      Author: juton
+ */
+
+#ifndef LIB_ENS_II1_LCD_H_
+#define LIB_ENS_II1_LCD_H_
+
+//definitions pour I2C
+#define I2CBAUD 		100000
+#define LCD_ADDR		0x7C
+#define BUFSIZE       	5
+
+void init_lcd(void);
+void lcd_puts();
+void lcd_putc(char c);
+void lcd_gohome();
+void lcd_position(char ligne, char colonne);
+
+#endif /* LIB_ENS_II1_LCD_H_ */